Wednesday, November 18, 2026

quasar, red and white triangle quilt, top completed

Quasar
85 by 69 inches
top completed 2026

I finished this top a few months ago and am finally getting to writing it up.

I've always liked this arrangement of triangles.
There are many commercial and free patterns out there but I came up with a setting method that works for my brain.

Mine is made from 4 inches finished half-square triangles pieced into 16-patch blocks.

I cut them from 4 1/2 inch strips using the Easy Angle or Bonnie Hunter's triangle tool.
White triangles (I used Kona Snow): 320
Red scrap triangles: 320

Sew intp 320 half-square triangles, pressing to the red.

I started with the center star block

note the dalmation makes its appearance! 
It is pieced as a 16-patch and every block in the quilt is pressed the same.
(The vertical seams are not pressed until the whole quilt is laid out and sewn into rows.)


Then, worked on the horizontal and vertical axes. 
This takes a bit of concentration but each block going from the center is the same.
Note I have 2 blocks going north and south from the center block and 1 1/2 blocks going east and west.
I made the blocks but sewed only the horizontal row together.

All seams of the horizontal row are pressed to the left.

Then I visually separated the outer quadrants into wedges as drawn here.
Laying out these blocks took more mind power, and a few mistakes happened along the way but were easily fixed.
I find if I take a photograph in low light the placement mistakes stand out.

These laid out units were then sewn into 16-patches (and half 16-patches on the left and right sides).
Sewn into rows; press the row seams to alternate and nest the rows into the top.
I added 3 inches cut borders.
Everything nests!

My directions for this design. Use at your pleasure.

bar quilt with step-ladders, top completed

Bar Quilt with step-ladders
96 by 80 inches
top completed 2026

When my 2 1/2 bins fill up I get to pull another idea from my sketchbook!
This uses the darks and brights 2 1/2 inch squares made into 16 patches and what I call step-ladder units made from 2 1/2 inch squares of Kona Ice Frappe and 1 1/2 by 2 1/2 inch darks and brights coins.
For this quilt I used:
1440 darks/brights 2 1/2 inch squares
320 darks/brights 2 1/2 by 1 1/2 inch rectangles
320 Kona Ice Frappe 2 1/2 by 1 1/2 inch rectangles

!6-patch sections--three bars
Each bar made with 30 16-patch blocks

Cut sixteen 2 1/2" squares to make each block (1440 for the quilt)
Sew into pairs, then fours
Press all to one side
Flip every other section and sew into 16-patch block, will nest
Make 90 blocks
Sew into pairs, press all seams to one side, flip the center pair sew the pairs into units of three pairs.
Wait to press the joining seams
Lay out 5 of the units, pressing the previous sewn joining seams alternating up and down. Join the units.
Make three bars


Step-ladder sections--two bars
Each bar made with 10 blocks (20 for the quilt)
Cut sixteen 2 2/12 inch square of solid for each block (320 for the quilt)
Cut sixteen 2 1/2 by 1 1/2 inch rectangle coin for each block (320 for the quilt)
Make 16 step-ladder units
Press to the dark coin
Sew into pairs then fours, press all consistanly to one side
Flip every other unit and sew into a block, will nest
Sew into two rows of 10, press rows all toards one direction
Lay out the bars, making sure to orient each bar so it will nest into the subsequent one.
Sew the bars together
Press horizontal seams south
Everything nests!
My design, use at your pleasure.
I have a Red and White variation in the works!
Alice came out to play!